Gemini motors and parts

bad 44u · Post by **bad 44u** » 10 Apr 2007, 09:38

For Sale
Rodeo 4ze1 2.6 race motor 48 mm webers 3inch exhaust
Trimatic suit z motor 2500 stall manualised trans cooler tail shaft
G180w Twin cam efi needs fuel pump and tune
2 x bare twin cam heads
twin cam pistons cams block and many other internal and external parts
Standard gemini diff 2 x good torque tube mounts
Slotted and cross drilled gemini front rotors standard calipers
Front suspension parts
Full original gemini interior good condition, zzz dash
Gemini fuel tank
5 x 13 inch rims
Stainless steel surge tank
10 inch thermo fan
ph 0431482093

G200-GEM · Post by **G200-GEM** » 12 Apr 2007, 14:16

hi mate would you seperate the twin webers from the engine? desperately wanting some

thanks

bad 44u · Post by **bad 44u** » 13 Apr 2007, 08:00

sorry its a complete package

GeminiCoupe · Post by **GeminiCoupe** » 14 Apr 2007, 15:00

What are you asking for the G180 DOHC and whats freight to melb worth?

bad 44u · Post by **bad 44u** » 16 Apr 2007, 09:43

$500. the motor is at my parents house in wollongong and i wont be up there for a couple weeks just in case you want it urgently. It had new rings and bearings put in it but it hasn't been started for about 3 years. the computer run's it ok but its an old type with screw adjusters on the computer.I had it dyno tuned i think it had 70 kw at the rears which is what you would expect for a standard twin cam needs a bigger throttle body and im taking the electronic ignition off it but i have the standard points distributor.
let me know if your still interested and ill check freight and make sure it still turns over.

archangel62 · Post by **archangel62** » 20 Apr 2007, 04:33

I might know a bloke interested in the engine, could you also check what freight to Adelaide would be worth?

If you have a spare G180W piston floating around (doesn't matter if it's cracked buggered etc etc as long as the shape's right) and are willing to sell it on it's own I might be interested, I'm just after a template piston and don't want to pull my engine apart.

I may also after a fuel pressure regulator.

bad 44u · Post by **bad 44u** » 20 Apr 2007, 08:18

are you after the standard fuel reg thats on the fuel rail or an aftermarket one. ill split a set of g180w pistons for $50 plus postage or the whole set for same. Are you getting forgies made if so i might be interested depending on what compression your going for.

archangel62 · Post by **archangel62** » 21 Apr 2007, 04:35

Yup. I'm going for around 8:1 to 8.2:1, not totally sure yet but yeah, for turbo. I'm sending off a piston to America and having them made by a reputable company, through my engine builder I should be able to get all of this done around the $1000 mark, not bad at all for international custom made.

As for the when... It's definitely not going to be soon, unless I win the lottery. I'm going to be up for about $3000 worth of turbo gear before I need these pistons anyway, and my engine isn't even running with the stock ones yet

.

I'm definitely interested in those pistons man, do you think you could figure out how much postage would be to Adelaide and let me know? A spare set can't hurt anyway...

Eli

G200-GEM · Post by **G200-GEM** » 22 Apr 2007, 22:37

hey eli why do a complete rebuild and then rebuild it again ?

archangel62 · Post by **archangel62** » 25 Apr 2007, 05:00

Funding really. I only had my car on the road (and license, driving legally lol) for about 8 months before it packed up. I've now had it off the road for 10 months or so, which is ridiculous, and I don't know how long it's gonna be before I can afford forgies, a decent turbo, intercooler etc etc (let alone the diff conversion to use the power).

I know its a bit of a waste but by the time I rip out the stock pistons and rings they will have copped a thrashing

. Plus then I have them as spares. Actually, come to think of it, I don't need a whole set of spares for this reason. Unless I get another twincam

lol. Plus, 120-140rwkw on stock pistons should keep me busy (read:sideways) for awhile

wattagan · Post by **wattagan** » 29 Oct 2007, 19:16

Hi Bad44U,
I'm interested in your
G180w Twin cam efi needs fuel pump and tune
2 x bare twin cam heads
I need a head and related bits to fit to a Rootes engine.

bad 44u · Post by **bad 44u** » 30 Oct 2007, 08:09

the g180 efi is gone but i have the other spare parts just let me know exactly and ill dig around and see what ive got